Application

Application

At what speed should microcement be sanded?

Use low to medium speeds and monitor both temperature and sanding aggressiveness.

Application

Can Aqua Nature be diluted with water?

Dilution is possible only according to the technical datasheet and must not compromise the properties or shade.

Application

Can Microcement Be Machine Sanded?

Yes, but with care to avoid over-sanding or circular marks.

Application

Can microcement be sanded by hand?

Yes, smaller areas, corners and repairs are commonly sanded by hand.

Application

Can Primer Plus be used on a non-absorbent substrate?

Yes, but it is advisable to check the appropriate preparation and adhesion on a non-absorbent substrate.

Application

Do I have to sand every layer of Aqua Base?

It is recommended at least to smooth out irregularities and sharp transitions between layers.

Application

How can I tell if it has been over-sanded?

Over-sanding is indicated by changes in the pattern, sanding through the layer, or uneven colour.

Application

How Do I Know That Aqua Base Is Dry?

It is not damp to the touch, feels firm, matt, not sticky, and does not tear when sanded.

Application

How is microcement applied step by step?

The basics are substrate preparation, priming, Aqua Base, final render, Gela Cryl and varnish.

Application

How Long Does Aqua Base Take to Dry?

Usually a few hours, but it depends on temperature, humidity, and layer thickness.

Application

How long does Aqua Nature take to dry?

The drying time depends on conditions, usually several hours between steps.

Application

How long does Primer Plus take to dry?

The drying time depends on temperature, humidity, and the absorbency of the substrate.

Application

How many layers of Aqua Base are applied?

Usually one layer; two layers may be applied for reinforcement and covering old tiles.

Application

How many layers of Aqua Nature are applied?

Usually one final layer for a uniform finish and coverage.

Application

How thick should the Aqua Base layer be?

The layer should be thin and continuous; its thickness depends on flatness and reinforcement.

Application

How to Apply Aqua Base?

Aqua Base is applied with a stainless steel trowel in a thin, even layer.

Application

How to Apply Aqua Nature?

Aqua Nature is applied in thin decorative layers using a stainless steel trowel.

Application

How to Apply Primer Plus?

Apply evenly with a roller or brush without puddles and allow to dry.

Application

How to Create a Distinctive Concrete Effect?

Use variable trowel strokes, varying pressure and natural joining of material, or a texturing roller.

Application

How to Create a Fine Finish?

Apply more evenly, in thin layers, and with less contrast in your strokes.

Application

How to Create a Stone Effect?

The effect is achieved by combining strokes, layering, and optionally gel patination.

Application

How to Create a Travertine Effect?

The travertine effect requires controlled strokes, delicate layering, and often a test sample.

Application

How to Prevent Stains During Application?

Maintain a consistent thickness, substrate absorbency, drying time, use a smooth technique and avoid coloured patination gel.

Application

How to Prevent Visible Joints?

Work wet on wet and divide the surface into logical sections.

Application

How to Remove Dust After Sanding?

Best done by thorough vacuuming with an industrial vacuum cleaner.

Application

How to sand Aqua Base?

It is sanded to remove edges, unevenness and trowel marks.

Application

How to Work in Corners?

Corners are handled carefully with smaller tools and without material build-up.

Application

How to work on a large surface?

Plan large surfaces with multiple people or in natural sections without sharp transitions.

Application

Is it possible to create highlights or patterns?

Yes, but it is advisable to make a sample first, as the result depends on the applicator’s technique.

Application

What Grit Should Be Used on Aqua Base?

Often P40–P80 depending on the unevenness and the desired smoothing.

Application

What Tools Do I Need for Application?

The basics are a trowel, rollers, abrasives, vacuum cleaner, mixer, tape, and protective equipment.

Application

Which Abrasive to Use?

The abrasive is chosen according to the layer; coarser for the base, finer for the final layers.

Application

Which float to use?

Most commonly a stainless steel float; for a finer finish, a plastic float can also be used.